Xprog V6.50 V6.26 V6.17 Add New Authorization Newest X-Prog M Metal Box Xprog-M Ecu Programmer X Prog M Full Adapters







ITEM 1:NEW Release XPROG V6.50 ,More Authorization Released
Software V6.50 Firmware V6.8
Attention For Xprog V6.50 Software Installation Tips:
1. MUST Connect Internet,use online(But DO NOT UPDATE)
2. PC Time MUST adjust to Accurate Local Time
3. MUST first install 6.50registry,then run V6.50 Software
4. After used,close the software and unplug the usb dongle from the computer
5. Better to use in English System
6. PDF MUST update to Newest Version from official site
Computer Requirement For V6.50:
1. Reuqire only Win 7 64bits
2. System Space at least have Space C and Sapce D . if only Space C ,software install failed and show error .
3. Close Anti-virus programmer
Please check below Xprog V6.50 New Added Authorization:
ITEM 2:XPROG V6.26
Please Attention For Xprog V6.26 Software Installation Tips:
1. MUST Connect Internet,use online(But DO NOT UPDATE)
2. PC Time MUST adjust to Accurate Local Time
3. MUST first install 6.26registry,then run V6.26 Software 4. After used,close the software and unplug the usb dongle from the computer
5. Better to use in English System
6.The computer's disk must have at least 2 or more partitions, such as C drive and D drive
Please must follow this instructions to run software,otherwise device will not installed.
Please MUST READ This :
1. Which XPROG version you use , before open software MUST install the right version registry. Otherwise it will runs old version registry automically and then confilt with new hardware and device dead.
2. If your computer no install other old xprog version,it also require install right registry ,otherwise device runs fault and defective .
XPROG V6.26 using tips:
1.XPROG V6.26 dongle isn't compatible with older version Xprog. You are not allowed to update from the older version Xprog V5.55 V5.60 V5.70 V5.84 V6.12 to this newest V6.26 XPROG-M Dongle.
2. Please Close all anti-virus software in your computer, because the anti-virus software will kill Xprog V6.26 driver and software
3. Uninstall all the old version XPROG software and registry before you install V6.26 software, because XPROG V6.26 hardware is not compatible with other version XPROG software. Otherwise the hardware will be damaged and its warranty will be invalid.
5. Never try to UPDATE it, the hardware will be damaged and lost authorization if you try to update it
online. Warranty will be invalid.
ITEM 3: XPROG V6.17
XPROG-M V6.17 Highlights:
1. Latest Software Version: V6.17, Firmware: V4.4
2. Adds new authorization: AUTH-0028-1 for Renesas V850 Authorized and AUTH-0028-2 for Renesas SuperH Authorized 2017/10/9
3. Operating System: WinXP/Win7 64BIT
4.Language: English only
Using Tips:
1. XPROG V6.17 now not have USB dongle.
2. Please Close all anti-virus software in your computer, becase the anti-virus software will kill Xprog V6.12 driver.
3. Disconnect internet. If not, the internet may damage XPROG hardware.
4. Uninstall all the old version XPROG software before you install V6.17 software, because XPROG V6.17 hardware is not compatible with other version XPROG software.
5.Never try to UPDATE it, the hardware will be damaged if you try to update it online.
Install Notice:
Error About Certifate Expired:
When buyer meet this problem ,it means your computer install other older version and didn't uninstall yet.and computer has old xprog software registry.red and didn't uninstall ,so it wil cause this problem .
Now you need buy ATMEGA 64 chip to reflash programmer and then next time must click 6.12registry and then run 6.12 software.
So No matter which version you use,before open software MUST click the right version registry .Otherwise it will runs old version registry and then confilt with new hardware and show this update error.
Package Includes:
1pc x XPROG-Box Hardware (Aluminum Enclosure)
19pc x Adapters Set
1pc x USB Cable
1pc x 16Pin cable
1pc x CD with XPROG-Box Software
Real Photo Show:
XPROG V6.50:
XPROG V6.26:
XPROG V6.17: