Track your order
623a1bd1cf09952bcb6bfbf3-regular
1800W 40A 1500W 30A 1200W 20A Dc-Dc Boost Converter Step Up Power Supply Module 10-60V To 12-90V Adjustable Voltage Cha

1800W 40A 1500W 30A 1200W 20A Dc-Dc Boost Converter Step Up Power Supply Module 10-60V To 12-90V Adjustable Voltage Cha

$26.95
2/7
description
product reviews 





 


 


 




Product Description



 



 





 



Product description:

The module output voltage, current adjustable, can boost, constant current

Input adjustable undervoltage protection, over temperature protection, short circuit protection, reverse connection protection.

1800W is designed for lead-acid batteries, lithium batteries, solar cells, or power boosters to boost electric vehicles and charge batteries. It is very powerful.

1. For example, the original battery of an electric vehicle is 48V and can be boosted to 60V to power the electric vehicle, which can increase the speed and acceleration of the electric vehicle.

2, for your electric bike charging, (A: For example, there is a 12V or 24 idle battery on hand, you can use this boost power supply to boost the original battery after charging, equivalent to an electric car charging treasure. 2: Simultaneous input Can also be connected to solar cells, wind power, generators and other power boosted to the original battery to increase the electric vehicle's battery life.)

3 The battery voltage can be increased to allow the electric vehicle to run faster, and the meter should not exceed 10V.

4 Solar panel boost voltage regulation.



Features:

1. With airfoil-type heat dissipation, the heat dissipation effect is very good, and the output power is even greater (the power of the 48V input and fan can reach around 1800W).

2. Temperature-controlled fans, with hydraulic bearing fans, have a very good balance between noise and heat dissipation. When the load is light, the fan does not rotate. After the temperature of the load reaches approximately 60 degrees, the fan automatically turns. Can effectively reduce noise and extend life.

3. The main power tube insulation board is made of high-grade alumina, and the thermal conductivity is 10 times that of ordinary insulation mats.

4. The 100V 210A TO-247 large package power tube has large power margin and good dynamic response.

5. Double large-size ferro-silica-aluminum magnetic rings, using four 1.2-pure copper enameled wires, with low heat generation and high efficiency.

6. With a new design, the conversion efficiency is as high as 98.1% (see the datasheet efficiency conversion curve below for details).

7. Brand 3296W multi-turn potentiometer, high adjustment accuracy, small drift.

8. Kang copper output current sampling, constant temperature and stable temperature drift small.

9. Undervoltage protection is adjustable, which can effectively protect a variety of batteries, and can also be used for solar cells.

10. With constant current function, it can be used for boosting the battery car, charging the battery and so on.

11. The input of 3 20A fuses in parallel can protect the risk of accidental short circuit in the output.

12. Three indicator lights: Undervoltage, overcurrent, power indication, working status at a glance.

13. The input and output are all high-frequency capacitors, low output ripple, low heat generation, and long life.

14. The MLCC ceramic capacitor is added to the input and output, and the output ripple is significantly reduced, which is about 100mV at 48V to 72V 4A.



Work Features:

Output power: 1800W

Input voltage range: 10V-60V

Output voltage range: 12V-90V

Input current: 40A

Output current: 22A

Dynamic response speed: load current change 5% (300us)

Conversion efficiency: 48V to 60V 8A (98.1%)

                       48V to 72V 8A (98.1%)

                       48V to 84V 8A (97.6%)

Load regulation: 10% to 50% load ((72V output))

Temperature coefficient: 50% load

Ripple & Noise: 20MHz Bandwidth (48V-72V 4A) 100mVp-p

Switching frequency: VIN=48V VO=72V 4A (110khz)

No-load current: VIN=48V VO=72V (18mA)

Output short circuit protection: YES

Input reverse protection: YES

Storage humidity: 95%

Working temperature: -20 65°C

Storage temperature: -40 125°C

Temperature rise during work: 48V to 60V 5A (45°C)

Over temperature protection: (60°C)

Wiring method: IN input, OUT output (No welding, terminal blocks)

Cooling method: Strong wind cooling

Appearance size: 130 (L) * 51 (W) * 80(H) ( with copper pillars) mm

Package Contents:

1800W 40A DC-DC Boost Converter Step Up Power Supply Module Constant Current

 



 



 Module name: 1500W boost constant current module

 Module nature: non-isolated boost module (BOOST)

 Input voltage: DC10-60V

 Input current: 10-30V input voltage, maximum current 30A

 31-60V input voltage, maximum current 25A

 Static working current: 15mA (when 12V rises to 20V, the higher the output voltage, the static current will increase

 plus)

 Output voltage: 12-90V continuously adjustable (default output is adjusted to 19V for shipment, if you need to adjust to other

 Please specify the voltage value. (If you have a multimeter, the buyer can adjust it yourself)

 12-90V fixed output (for batch customers)

 Output current: 20A MAX Please strengthen heat dissipation if it exceeds 15A (related to the input and output pressure difference,

 The greater the pressure difference, the smaller the output current)

 Constant current range: 0.8-20A (+/-0.3A)

 Input anti-reverse connection: Yes (150A power MOS anti-reverse)

 Low battery protection: Yes (8-50V adjustable) self-recovery type

 Working temperature: -40~+85 degrees (please strengthen heat dissipation when the ambient temperature is too high)

 Working frequency: 150KHz

  Conversion efficiency: 92%-97% (efficiency is related to input, output voltage, current, pressure difference. Small pressure difference, high efficiency)

  Input overcurrent protection: Yes (input over 35A, automatic protection, power supply does not boost)

  Short circuit protection: Yes (input 30A fuse) double short circuit protection, safer to use.

  Input reverse connection protection: Yes (150A power MOS tube anti-reverse. It can be reversed for a long time)

   Installation method: 4 3mm copper pillars

   Connection method: terminal block (please use high-current pure copper wire)

   Module size: length 130mm, width 52mm, height 84mm (high including copper pillar and fan), length 130mm, width 52mm, height 67mm (high without copper pillar and fan)

   Module weight: 490 grams

  Output power: = input voltage*30A, such as: input 12V*30A=360W, the maximum power when inputting 12V is 360W

 Input voltage*30A such as: input 24V*30A=720W, that is, the maximum power when inputting 24V is 720W

Power description:

       Since the maximum input current of this power supply is 30A at 10-30V and 25A at 31-60V, the output power is related to the input voltage. The higher the input voltage, the higher the power,

(Input voltage * input current equals the power of the whole machine) For example, the input 12V*30A power is 360W. The input 24V*30A is 720W. When the input voltage is 36V, the maximum input current is 25A. The maximum power of the power supply is 900W.

main advantage:

1. The power supply uses four 1.2mm pure copper wires with double iron silicon aluminum. 100V/210A low resistance power MOS, high power and high current input, suitable for high power LED, motor use

2. There is input MOS anti-reverse connection protection, so there is no need to worry about the input connection and burn out the power supply

3. Low battery protection will not damage the power module and battery due to battery over-discharge when using battery input.

5. Thick radiator and intelligent temperature control fan for heat dissipation.

Voltage regulation:

Use a flat-blade screwdriver to adjust the output terminal “V-ADJ” potentiometer (marked in the figure below) when the power is turned on and there is no load. Turn clockwise to increase and counterclockwise to decrease). Due to the large capacity of the output capacitor, the output voltage is The response will be slower when the high voltage is adjusted to the low voltage. The adjustment range of the instrument is smaller. (The default output voltage is adjusted to 19V for shipment. If we need to adjust other voltage values, please explain or leave a message)

Current regulation:

Turn the "CC A-ADJ" potentiometer counterclockwise about 30 turns, set the output current to the minimum, connect the LED battery and other loads, and adjust the "CC A-ADJ" potentiometer clockwise to the current you need. For battery charging, after the battery is discharged, connect to the output and adjust CC A-ADJ to the current you need. When charging, you must use the discharged battery to adjust it, because the battery is left The more power, the lower the charging current. The default output ESC is shipped to 3A. If we need to adjust the current value adjustment instructions or leave a message. Do not use the short-circuit output method to adjust the current. The circuit structure of the boost module cannot be adjusted by the short-circuit method.



 



Item pictures





 
























 



 



 



 





For more offers, please click on the link below.





 



For Arduno module         DC-DC power module          Wireless Module         Amplifier board  



    Sensor module                Relay module                 Bluetooth module        for wemos d1 mini



Servo and Motor            LCD            Digital Voltmeter   



   3D Printers          Raspberry series          Breadboard   



Jump wire        LED              others










2/7

1800W 40A 1500W 30A 1200W 20A Dc-Dc Boost Converter Step Up Power Supply Module 10-60V To 12-90V Adjustable Voltage Cha

$26.95
Shipping info

Shipments will deliver in 10 to 20 business days.


Learn more about our shipping rates here and our returns, refunds, and exchanges policy here.
Keywords & Tags